PULSATION DAMPENERS. Urethane Bladder. EMSCO PD - 43/45. EMSCO PD - 53/55. KB45 same as PD - 43/45. KB75 same as PD - 53/55. Pulsation Bladder. Hydril K-10 (same as Sumlar) P/N #41586. Hydril K-20 (same as GP Matco) P/N #35504. EMSCO PD - 43/45 (12 gallon) P/N #6922-0086-00. EMSCO PD - 53/55 (20 gallon) P/N #6922-003-00. Recommended location for the pulsation control equipment is within 6 times the nominal pipe diameter of the pump discharge manifold. Discharge damp-eners are not effective when installed away from the pump. M20-7500 (Pneumatic Discharge Dampener with Nitrogen Charge) The 20 gallon pneumatic discharge dampener has been the drilling industry. 825 hydril pulsation dampener products are offered for sale by suppliers on Alibaba.com, of which mining machinery parts accounts for 1%, mud pump accounts for 1%, and other rubber products accounts for 1%. A wide variety of hydril pulsation dampener options are available to you, There are 25 suppliers who sells hydril pulsation dampener on.

1. Hydril K20 Pulsation Dampener Manual
2. Hydril Pulsation Dampener Manual Instructions
3. Hydril K20 Pulsation Dampener Manual
4. Hydril Pulsation Distributor

SFU Series

1. SFU o-ring
2. SFU wing nut
3. Dust cap
4. Loading valve
5. Bleeder valve
6. Cartridge
7. Case

SFV & SFVM Series

1. 6″ or 8″ suction gasket
2. 6″ or 8″ grooved coupling
3. Dust cap
4. Loading valve
5. Bleeder valve
6. Cartridge
7. Case

SFT Series

1. HPG-1 gasket (Nitrile or EPDM)
3. Dust cap
4. Loading valve
5. Bleeder valve
6. Cartridge
7. Case

SFM Series

1. SFM o-rings (2 required)
2. SFM wingnut
3. Dust cap
4. Loading valve
5. Bleeder valve
6. Cartridge
7. Case
8. SFM wingnut screw

CHARGE TO 80%- 90% OF SUCTION PRESSURE OR THE MAXIMUM CHARGE PRESSURE OF THE CARTRIDGE, WHICHEVER IS LESS. THIS IS ONLY AN APPROXIMATION.

(YOU MAY FIND IT NECESSARY TO DECREASE THE PRESSURE IN THE SUCTION CARTRIDGE TO ACHIEVE OPTIMUM PUMP PERFORMANCE.)

1. Shut down pump and relieve line pressure from discharge side before closing suction valve. After discharge line is relieved of pressure, close suction line valve and drain suction line.
2. Open bleeder valve ’A’.
3. Remove loading valve protector cap ’B’.
4. Remove cap from loading valve ’C’.
5. Loosen safety nut ’D’ three full turns.
6. Using NITROGEN ONLY, charge the cartridge through loading valve ’C’ to the recommended operating pressure (90% of suction pressure). (DO NOT EXCEED MAXIMUM CARTRIDGE CHARGE PRESSURE).
7. Tighten safety nut ’D’ on loading valve ’C’.
8. Replace loading valve protector cap ’B’
9. Open suction valve. When air from bleeder valve ’A’ is evacuated, close bleeder valve ’A’.

1. Shut down pump and relieve line pressure.
2. Open bleeder valve ’A’.
3. Remove loading valve protector cap ’B’.
4. Remove cap from loading valve ’C’.
5. Loosen safety nut ’D’ three full turns.
6. Using NITROGEN ONLY charge the cartridge through loading valve ’C’ to correct charge pressure (use chart below).
   NOTE: DO NOT EXCEED MAXIMUM CARTRIDGE CHARGE PRESSURE (ON CASE LABEL).
   
7. Tighten safety nut ’D’ on loading valve ’C’ and replace cap.
8. Replace loading valve protector cap ’B’.
9. Open suction valve. When air from bleeder valve ’A’ is evacuated, close bleeder valve ’A’.

WARNING

THE USE OF ANY GAS OTHER THAN NITROGEN IS EXTREMELY DANGEROUS.

NEVER ATTEMPT TO CHARGE OR PRE-CHARGE A CARTRIDGE OUTSIDE OF THE PULSATION STABILIZER CASE.

FOR PROPER CHARGING PROCEDURES REFER TO THE SUCTION OR DISCHARGE CHARGING GUIDE.

HYDRIL K20 Pulsation Bladders / Dampener and Bladder Kits

IPD^TM – PPD (Production Pulsation Dampener Diaphragms

IKD^TM – DPD (Drilling Pulsa tion Dampner Diaphragms)

Description	Hydril K20 Pulsation Dampener Manual Location 402 - Kamalalaya center, 156 A-Lenin Sarani,Kolkata-700 013, IndiaEmail: info@rrpcindia.com Links Hydril Pulsation Dampener Manual Instructions Hydril K20 Pulsation Dampener Manual Quick Links Hydril Pulsation Distributor © 2019 Rubber Regenerating & Processing Co. Powered By BTN Infosolution